diff options
| -rw-r--r-- | site/sony-wf1000xm3-battery.html | 22 | ||||
| -rw-r--r-- | src/inc/sony-wf1000xm3-battery.htm | 22 | ||||
| -rw-r--r-- | src/inc/sony-wf1000xm3-battery.md | 28 |
3 files changed, 35 insertions, 37 deletions
diff --git a/site/sony-wf1000xm3-battery.html b/site/sony-wf1000xm3-battery.html index 2ce2aec..735c8e6 100644 --- a/site/sony-wf1000xm3-battery.html +++ b/site/sony-wf1000xm3-battery.html @@ -48,7 +48,7 @@ them and use them mostly around the city to listen to podcasts and the occasional bit of music.</p> <p><img src="/media/content/sony-wf1000xm3-battery/headphones.jpg" class="size-l" /></p> -<p>After they would first slowly show signs of not holding their full +<p>After they slowly started showing signs of not holding their full charge anymore, the batteries completely died on me after some 3 years. I was fully prepared to have to throw them out when I learned that the batteries are just standard cells and can be easily swapped.</p> @@ -64,21 +64,21 @@ batteries are just standard cells and can be easily swapped.</p> class="size-s" alt="pry open" /> <img src="/media/content/sony-wf1000xm3-battery/02_lid_off.jpg" class="size-s" alt="lid off" /></p> -<p>Use a spudger or ideally two guitar picks and wedge them in to the +<p>Use a spudger or ideally two guitar picks and wedge them into the thin gap between the top cover and the base of the earphones. Don’t -worry about breaking anything. As long as the material of your tools is -plastic, you won’t damage anything. This is by far the most tedious step -of the process (if you don’t have the picks). There is a little bit of -adhesive behind the lid, so once you get the halfs to seperate you might -have to widdgle a little.</p> +worry about breaking anything, as long as the material of your tools is +plastic, you won’t damage the headphones. This is by far the most +tedious step of the process (if you don’t have the picks). There is a +little bit of adhesive behind the lid, so once you get the halfs to +seperate you might have to wiggle them loose.</p> <p><img src="/media/content/sony-wf1000xm3-battery/03_screws_out.jpg" class="size-s" alt="screws out" /> <img src="/media/content/sony-wf1000xm3-battery/04_lift_top.jpg" class="size-s" alt="lift top" /></p> -<p>With the phillips head remove the two screws that secure the visible -part in place and then carefully lift it out, flip it over. There is a -ribbon cable connecting the touch sensor and LED on the top to PCB -deeper inside the earpiece.</p> +<p>With the Phillips-head remove the two screws that secure the visible +part in place and then carefully lift it out and flip it over. There is +a ribbon cable connecting the touch sensor and LED on the top to PCB +inside the earpiece.</p> <figure> <img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg" class="size-s" alt="battery out" /> diff --git a/src/inc/sony-wf1000xm3-battery.htm b/src/inc/sony-wf1000xm3-battery.htm index 6f7bbd6..1031721 100644 --- a/src/inc/sony-wf1000xm3-battery.htm +++ b/src/inc/sony-wf1000xm3-battery.htm @@ -9,7 +9,7 @@ them and use them mostly around the city to listen to podcasts and the occasional bit of music.</p> <p><img src="/media/content/sony-wf1000xm3-battery/headphones.jpg" class="size-l" /></p> -<p>After they would first slowly show signs of not holding their full +<p>After they slowly started showing signs of not holding their full charge anymore, the batteries completely died on me after some 3 years. I was fully prepared to have to throw them out when I learned that the batteries are just standard cells and can be easily swapped.</p> @@ -25,21 +25,21 @@ batteries are just standard cells and can be easily swapped.</p> class="size-s" alt="pry open" /> <img src="/media/content/sony-wf1000xm3-battery/02_lid_off.jpg" class="size-s" alt="lid off" /></p> -<p>Use a spudger or ideally two guitar picks and wedge them in to the +<p>Use a spudger or ideally two guitar picks and wedge them into the thin gap between the top cover and the base of the earphones. Don’t -worry about breaking anything. As long as the material of your tools is -plastic, you won’t damage anything. This is by far the most tedious step -of the process (if you don’t have the picks). There is a little bit of -adhesive behind the lid, so once you get the halfs to seperate you might -have to widdgle a little.</p> +worry about breaking anything, as long as the material of your tools is +plastic, you won’t damage the headphones. This is by far the most +tedious step of the process (if you don’t have the picks). There is a +little bit of adhesive behind the lid, so once you get the halfs to +seperate you might have to wiggle them loose.</p> <p><img src="/media/content/sony-wf1000xm3-battery/03_screws_out.jpg" class="size-s" alt="screws out" /> <img src="/media/content/sony-wf1000xm3-battery/04_lift_top.jpg" class="size-s" alt="lift top" /></p> -<p>With the phillips head remove the two screws that secure the visible -part in place and then carefully lift it out, flip it over. There is a -ribbon cable connecting the touch sensor and LED on the top to PCB -deeper inside the earpiece.</p> +<p>With the Phillips-head remove the two screws that secure the visible +part in place and then carefully lift it out and flip it over. There is +a ribbon cable connecting the touch sensor and LED on the top to PCB +inside the earpiece.</p> <figure> <img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg" class="size-s" alt="battery out" /> diff --git a/src/inc/sony-wf1000xm3-battery.md b/src/inc/sony-wf1000xm3-battery.md index e617c2b..4f324f4 100644 --- a/src/inc/sony-wf1000xm3-battery.md +++ b/src/inc/sony-wf1000xm3-battery.md @@ -10,7 +10,7 @@ music. {class=size-l} -After they would first slowly show signs of not holding their full charge +After they slowly started showing signs of not holding their full charge anymore, the batteries completely died on me after some 3 years. I was fully prepared to have to throw them out when I learned that the batteries are just standard cells and can be easily swapped. @@ -27,20 +27,19 @@ Ok, let's go: {class="size-s"} {class="size-s"} -Use a spudger or ideally two guitar picks and wedge them in to the thin gap +Use a spudger or ideally two guitar picks and wedge them into the thin gap between the top cover and the base of the earphones. Don't worry about breaking -anything. As long as the material of your tools is plastic, you won't damage -anything. This is by far the most tedious step of the process (if you don't -have the picks). There is a little bit of adhesive behind the lid, so once you -get the halfs to seperate you might have to widdgle a little. +anything, as long as the material of your tools is plastic, you won't damage +the headphones. This is by far the most tedious step of the process (if you +don't have the picks). There is a little bit of adhesive behind the lid, so +once you get the halfs to seperate you might have to wiggle them loose. {class="size-s"} {class="size-s"} -With the phillips head remove the two screws that secure the visible part in -place and then carefully lift it out, flip it over. There is a ribbon cable -connecting the touch sensor and LED on the top to PCB deeper inside the -earpiece. +With the Phillips-head remove the two screws that secure the visible part in +place and then carefully lift it out and flip it over. There is a ribbon cable +connecting the touch sensor and LED on the top to PCB inside the earpiece. {class="size-s"} @@ -55,10 +54,9 @@ pushed it back into the housing. Before putting in the new battery make sure to check the writing on it or use the shape as a reference to figure out which side is the negative pole. Put -that side down, touching to the contacts. -The replacement batteries I got where a different brand and had all the -labeling on the plus pole. While the original VARTA branded batteries had it -exactly reversed. On my first attempt I didn't pay attention and put them in -the wrong way around. +that side down, touching to the contacts. The replacement batteries I got where +a different brand and had all the labeling on the plus pole. While the original +VARTA branded batteries had it exactly reversed. On my first attempt I didn't +pay attention and put them in the wrong way around.  |