diff options
| -rw-r--r-- | site/sony-wf1000xm3-battery.html | 69 | ||||
| -rw-r--r-- | src/inc/sony-wf1000xm3-battery.htm | 67 | ||||
| -rw-r--r-- | src/inc/sony-wf1000xm3-battery.md | 16 |
3 files changed, 87 insertions, 65 deletions
diff --git a/site/sony-wf1000xm3-battery.html b/site/sony-wf1000xm3-battery.html index 30cc1c4..e787f83 100644 --- a/site/sony-wf1000xm3-battery.html +++ b/site/sony-wf1000xm3-battery.html @@ -56,38 +56,47 @@ batteries are just standard cells and can be easily swapped.</p> </ul> <p>Ok, let’s go:</p> <p><img src="/media/content/sony-wf1000xm3-battery/01_pry_open.jpg" -class="size-s float-l" alt="pry open" /> <img +class="size-s" alt="pry open" /> <img src="/media/content/sony-wf1000xm3-battery/02_lid_off.jpg" -class="size-s float-l" alt="lid off" /> Use a spudger or ideally two -guitar picks and wedge them in to the thin gap between the top cover and -the base of the earphones. Don’t worry about breaking anything. As long -as the material of your tools is plastic, you won’t damage anything. -This is by far the most tedious step of the process (if you don’t have -the picks). There is a little bit of adhesive behind the lid, so once -you get the halfs to seperate you might have to widdgle a little.</p> +class="size-s" alt="lid off" /></p> +<p>Use a spudger or ideally two guitar picks and wedge them in to the +thin gap between the top cover and the base of the earphones. Don’t +worry about breaking anything. As long as the material of your tools is +plastic, you won’t damage anything. This is by far the most tedious step +of the process (if you don’t have the picks). There is a little bit of +adhesive behind the lid, so once you get the halfs to seperate you might +have to widdgle a little.</p> <p><img src="/media/content/sony-wf1000xm3-battery/03_screws_out.jpg" -class="size-s float-r" alt="screws out" /> <img +class="size-s" alt="screws out" /> <img src="/media/content/sony-wf1000xm3-battery/04_lift_top.jpg" -class="size-s float-r" alt="lift top" /> With the phillips head remove -the two screws that secure the visible part in place and then carefully -lift it out, flip it over. There is a ribbon cable connecting the touch -sensor and LED on the top to PCB deeper inside the earpiece.</p> -<p><img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg" -class="size-s float-l" alt="battery out" /> To remove the old battery I -found it easiest to push the spudger into the little gap in the plastic -where the ribbon cable connects to the top part. It is also glued in; be -careful not to pull out the contact points as well. If possible try to -preserve the glue, it will come in handy when securing the new battery -in place. I also scraped off what was stuck to the old battery and -pushed it back into the housing.</p> -<p><img src="/media/content/sony-wf1000xm3-battery/06_battery_in.jpg" -class="size-s float-r" alt="battery in" /> Before putting in the new -battery make sure to check the writing on it or use the shape as a -reference to figure out which side is the negative pole. Put that side -down, touching to the contacts. The replacement batteries I got where a -different brand and had all the labeling on the plus pole. While the -original VARTA branded batteries had it exactly reversed. On my first -attempt I didn’t pay attention and put them in the wrong way around.</p> +class="size-s" alt="lift top" /></p> +<p>With the phillips head remove the two screws that secure the visible +part in place and then carefully lift it out, flip it over. There is a +ribbon cable connecting the touch sensor and LED on the top to PCB +deeper inside the earpiece.</p> +<figure> +<img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg" +class="size-s" alt="battery out" /> +<figcaption aria-hidden="true">battery out</figcaption> +</figure> +<p>To remove the old battery I found it easiest to push the spudger into +the little gap in the plastic where the ribbon cable connects to the top +part. It is also glued in; be careful not to pull out the contact points +as well. If possible try to preserve the glue, it will come in handy +when securing the new battery in place. I also scraped off what was +stuck to the old battery and pushed it back into the housing.</p> +<figure> +<img src="/media/content/sony-wf1000xm3-battery/06_battery_in.jpg" +class="size-s" alt="battery in" /> +<figcaption aria-hidden="true">battery in</figcaption> +</figure> +<p>Before putting in the new battery make sure to check the writing on +it or use the shape as a reference to figure out which side is the +negative pole. Put that side down, touching to the contacts. The +replacement batteries I got where a different brand and had all the +labeling on the plus pole. While the original VARTA branded batteries +had it exactly reversed. On my first attempt I didn’t pay attention and +put them in the wrong way around.</p> <figure> <img src="/media/content/sony-wf1000xm3-battery/battery_comparison.jpg" alt="battery comparison" /> @@ -95,7 +104,7 @@ alt="battery comparison" /> </figure> </main> <footer> -Edited on 2025-04-16 <a href="https://git.sr.ht/~robertgzr/site/tree/master/src/inc/sony-wf1000xm3-battery.htm" target="_blank">[src]</a> +Edited on 2025-11-22 <a href="https://git.sr.ht/~robertgzr/site/tree/master/src/inc/sony-wf1000xm3-battery.htm" target="_blank">[src]</a> <a href="mailto:~robertgzr/public-inbox@lists.sr.ht">[comments]</a> <br> <b>robertgzr</b> diff --git a/src/inc/sony-wf1000xm3-battery.htm b/src/inc/sony-wf1000xm3-battery.htm index 60709e3..6f7bbd6 100644 --- a/src/inc/sony-wf1000xm3-battery.htm +++ b/src/inc/sony-wf1000xm3-battery.htm @@ -22,38 +22,47 @@ batteries are just standard cells and can be easily swapped.</p> </ul> <p>Ok, let’s go:</p> <p><img src="/media/content/sony-wf1000xm3-battery/01_pry_open.jpg" -class="size-s float-l" alt="pry open" /> <img +class="size-s" alt="pry open" /> <img src="/media/content/sony-wf1000xm3-battery/02_lid_off.jpg" -class="size-s float-l" alt="lid off" /> Use a spudger or ideally two -guitar picks and wedge them in to the thin gap between the top cover and -the base of the earphones. Don’t worry about breaking anything. As long -as the material of your tools is plastic, you won’t damage anything. -This is by far the most tedious step of the process (if you don’t have -the picks). There is a little bit of adhesive behind the lid, so once -you get the halfs to seperate you might have to widdgle a little.</p> +class="size-s" alt="lid off" /></p> +<p>Use a spudger or ideally two guitar picks and wedge them in to the +thin gap between the top cover and the base of the earphones. Don’t +worry about breaking anything. As long as the material of your tools is +plastic, you won’t damage anything. This is by far the most tedious step +of the process (if you don’t have the picks). There is a little bit of +adhesive behind the lid, so once you get the halfs to seperate you might +have to widdgle a little.</p> <p><img src="/media/content/sony-wf1000xm3-battery/03_screws_out.jpg" -class="size-s float-r" alt="screws out" /> <img +class="size-s" alt="screws out" /> <img src="/media/content/sony-wf1000xm3-battery/04_lift_top.jpg" -class="size-s float-r" alt="lift top" /> With the phillips head remove -the two screws that secure the visible part in place and then carefully -lift it out, flip it over. There is a ribbon cable connecting the touch -sensor and LED on the top to PCB deeper inside the earpiece.</p> -<p><img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg" -class="size-s float-l" alt="battery out" /> To remove the old battery I -found it easiest to push the spudger into the little gap in the plastic -where the ribbon cable connects to the top part. It is also glued in; be -careful not to pull out the contact points as well. If possible try to -preserve the glue, it will come in handy when securing the new battery -in place. I also scraped off what was stuck to the old battery and -pushed it back into the housing.</p> -<p><img src="/media/content/sony-wf1000xm3-battery/06_battery_in.jpg" -class="size-s float-r" alt="battery in" /> Before putting in the new -battery make sure to check the writing on it or use the shape as a -reference to figure out which side is the negative pole. Put that side -down, touching to the contacts. The replacement batteries I got where a -different brand and had all the labeling on the plus pole. While the -original VARTA branded batteries had it exactly reversed. On my first -attempt I didn’t pay attention and put them in the wrong way around.</p> +class="size-s" alt="lift top" /></p> +<p>With the phillips head remove the two screws that secure the visible +part in place and then carefully lift it out, flip it over. There is a +ribbon cable connecting the touch sensor and LED on the top to PCB +deeper inside the earpiece.</p> +<figure> +<img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg" +class="size-s" alt="battery out" /> +<figcaption aria-hidden="true">battery out</figcaption> +</figure> +<p>To remove the old battery I found it easiest to push the spudger into +the little gap in the plastic where the ribbon cable connects to the top +part. It is also glued in; be careful not to pull out the contact points +as well. If possible try to preserve the glue, it will come in handy +when securing the new battery in place. I also scraped off what was +stuck to the old battery and pushed it back into the housing.</p> +<figure> +<img src="/media/content/sony-wf1000xm3-battery/06_battery_in.jpg" +class="size-s" alt="battery in" /> +<figcaption aria-hidden="true">battery in</figcaption> +</figure> +<p>Before putting in the new battery make sure to check the writing on +it or use the shape as a reference to figure out which side is the +negative pole. Put that side down, touching to the contacts. The +replacement batteries I got where a different brand and had all the +labeling on the plus pole. While the original VARTA branded batteries +had it exactly reversed. On my first attempt I didn’t pay attention and +put them in the wrong way around.</p> <figure> <img src="/media/content/sony-wf1000xm3-battery/battery_comparison.jpg" alt="battery comparison" /> diff --git a/src/inc/sony-wf1000xm3-battery.md b/src/inc/sony-wf1000xm3-battery.md index 1c799c2..e617c2b 100644 --- a/src/inc/sony-wf1000xm3-battery.md +++ b/src/inc/sony-wf1000xm3-battery.md @@ -24,8 +24,9 @@ Before you start, get the following: Ok, let's go: -{class="size-s float-l"} -{class="size-s float-l"} +{class="size-s"} +{class="size-s"} + Use a spudger or ideally two guitar picks and wedge them in to the thin gap between the top cover and the base of the earphones. Don't worry about breaking anything. As long as the material of your tools is plastic, you won't damage @@ -33,14 +34,16 @@ anything. This is by far the most tedious step of the process (if you don't have the picks). There is a little bit of adhesive behind the lid, so once you get the halfs to seperate you might have to widdgle a little. -{class="size-s float-r"} -{class="size-s float-r"} +{class="size-s"} +{class="size-s"} + With the phillips head remove the two screws that secure the visible part in place and then carefully lift it out, flip it over. There is a ribbon cable connecting the touch sensor and LED on the top to PCB deeper inside the earpiece. -{class="size-s float-l"} +{class="size-s"} + To remove the old battery I found it easiest to push the spudger into the little gap in the plastic where the ribbon cable connects to the top part. It is also glued in; be careful not to pull out the contact points as well. If @@ -48,7 +51,8 @@ possible try to preserve the glue, it will come in handy when securing the new battery in place. I also scraped off what was stuck to the old battery and pushed it back into the housing. -{class="size-s float-r"} +{class="size-s"} + Before putting in the new battery make sure to check the writing on it or use the shape as a reference to figure out which side is the negative pole. Put that side down, touching to the contacts. |