adapt sony-wf1000xm3-battery page to new styles

Signed-off-by: Robert Günzler <r@gnzler.io>

1 files changed, 7 insertions, 7 deletions

diff --git a/src/inc/sony-wf1000xm3-battery.md b/src/inc/sony-wf1000xm3-battery.md
index af910b8..1c799c2 100644
--- a/src/inc/sony-wf1000xm3-battery.md
+++ b/src/inc/sony-wf1000xm3-battery.md
@@ -8,7 +8,7 @@ I've had these since 2021, while they are a bit bulky I am happy with them and
 use them mostly around the city to listen to podcasts and the occasional bit of
 music. 
 
-![](/media/content/sony-wf1000xm3-battery/headphones.jpg)
+![](/media/content/sony-wf1000xm3-battery/headphones.jpg){class=size-l}
 
 After they would first slowly show signs of not holding their full charge
 anymore, the batteries completely died on me after some 3 years. I was fully
@@ -24,8 +24,8 @@ Before you start, get the following:
 
 Ok, let's go:
 
-![pry open](/media/content/sony-wf1000xm3-battery/01_pry_open.jpg){class="sm left"}
-![lid off](/media/content/sony-wf1000xm3-battery/02_lid_off.jpg){class="sm right"}
+![pry open](/media/content/sony-wf1000xm3-battery/01_pry_open.jpg){class="size-s float-l"}
+![lid off](/media/content/sony-wf1000xm3-battery/02_lid_off.jpg){class="size-s float-l"}
 Use a spudger or ideally two guitar picks and wedge them in to the thin gap
 between the top cover and the base of the earphones. Don't worry about breaking
 anything. As long as the material of your tools is plastic, you won't damage
@@ -33,14 +33,14 @@ anything. This is by far the most tedious step of the process (if you don't
 have the picks). There is a little bit of adhesive behind the lid, so once you
 get the halfs to seperate you might have to widdgle a little.
 
-![screws out](/media/content/sony-wf1000xm3-battery/03_screws_out.jpg){class="sm left"}
-![lift top](/media/content/sony-wf1000xm3-battery/04_lift_top.jpg){class="sm right"}
+![screws out](/media/content/sony-wf1000xm3-battery/03_screws_out.jpg){class="size-s float-r"}
+![lift top](/media/content/sony-wf1000xm3-battery/04_lift_top.jpg){class="size-s float-r"}
 With the phillips head remove the two screws that secure the visible part in
 place and then carefully lift it out, flip it over. There is a ribbon cable
 connecting the touch sensor and LED on the top to PCB deeper inside the
 earpiece.
 
-![battery out](/media/content/sony-wf1000xm3-battery/05_battery_out.jpg){class="sm left"}
+![battery out](/media/content/sony-wf1000xm3-battery/05_battery_out.jpg){class="size-s float-l"}
 To remove the old battery I found it easiest to push the spudger into the
 little gap in the plastic where the ribbon cable connects to the top part. It
 is also glued in; be careful not to pull out the contact points as well. If
@@ -48,7 +48,7 @@ possible try to preserve the glue, it will come in handy when securing the new
 battery in place. I also scraped off what was stuck to the old battery and
 pushed it back into the housing.
 
-![battery in](/media/content/sony-wf1000xm3-battery/06_battery_in.jpg){class="sm right"}
+![battery in](/media/content/sony-wf1000xm3-battery/06_battery_in.jpg){class="size-s float-r"}
 Before putting in the new battery make sure to check the writing on it or use
 the shape as a reference to figure out which side is the negative pole. Put
 that side down, touching to the contacts.