From ba619b4f1a83292570159fb29c4e3997718f8f04 Mon Sep 17 00:00:00 2001
From: Robert Günzler <r@gnzler.io>
Date: Sat, 22 Nov 2025 20:43:31 +0100
Subject: sony-wf1000xm3-battery: improve formatting
MIME-Version: 1.0
Content-Type: text/plain; charset=UTF-8
Content-Transfer-Encoding: 8bit

Signed-off-by: Robert Günzler <r@gnzler.io>
---
 src/inc/sony-wf1000xm3-battery.htm | 67 +++++++++++++++++++++-----------------
 1 file changed, 38 insertions(+), 29 deletions(-)

(limited to 'src/inc/sony-wf1000xm3-battery.htm')

diff --git a/src/inc/sony-wf1000xm3-battery.htm b/src/inc/sony-wf1000xm3-battery.htm
index 60709e3..6f7bbd6 100644
--- a/src/inc/sony-wf1000xm3-battery.htm
+++ b/src/inc/sony-wf1000xm3-battery.htm
@@ -22,38 +22,47 @@ batteries are just standard cells and can be easily swapped.</p>
 </ul>
 <p>Ok, let’s go:</p>
 <p><img src="/media/content/sony-wf1000xm3-battery/01_pry_open.jpg"
-class="size-s float-l" alt="pry open" /> <img
+class="size-s" alt="pry open" /> <img
 src="/media/content/sony-wf1000xm3-battery/02_lid_off.jpg"
-class="size-s float-l" alt="lid off" /> Use a spudger or ideally two
-guitar picks and wedge them in to the thin gap between the top cover and
-the base of the earphones. Don’t worry about breaking anything. As long
-as the material of your tools is plastic, you won’t damage anything.
-This is by far the most tedious step of the process (if you don’t have
-the picks). There is a little bit of adhesive behind the lid, so once
-you get the halfs to seperate you might have to widdgle a little.</p>
+class="size-s" alt="lid off" /></p>
+<p>Use a spudger or ideally two guitar picks and wedge them in to the
+thin gap between the top cover and the base of the earphones. Don’t
+worry about breaking anything. As long as the material of your tools is
+plastic, you won’t damage anything. This is by far the most tedious step
+of the process (if you don’t have the picks). There is a little bit of
+adhesive behind the lid, so once you get the halfs to seperate you might
+have to widdgle a little.</p>
 <p><img src="/media/content/sony-wf1000xm3-battery/03_screws_out.jpg"
-class="size-s float-r" alt="screws out" /> <img
+class="size-s" alt="screws out" /> <img
 src="/media/content/sony-wf1000xm3-battery/04_lift_top.jpg"
-class="size-s float-r" alt="lift top" /> With the phillips head remove
-the two screws that secure the visible part in place and then carefully
-lift it out, flip it over. There is a ribbon cable connecting the touch
-sensor and LED on the top to PCB deeper inside the earpiece.</p>
-<p><img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg"
-class="size-s float-l" alt="battery out" /> To remove the old battery I
-found it easiest to push the spudger into the little gap in the plastic
-where the ribbon cable connects to the top part. It is also glued in; be
-careful not to pull out the contact points as well. If possible try to
-preserve the glue, it will come in handy when securing the new battery
-in place. I also scraped off what was stuck to the old battery and
-pushed it back into the housing.</p>
-<p><img src="/media/content/sony-wf1000xm3-battery/06_battery_in.jpg"
-class="size-s float-r" alt="battery in" /> Before putting in the new
-battery make sure to check the writing on it or use the shape as a
-reference to figure out which side is the negative pole. Put that side
-down, touching to the contacts. The replacement batteries I got where a
-different brand and had all the labeling on the plus pole. While the
-original VARTA branded batteries had it exactly reversed. On my first
-attempt I didn’t pay attention and put them in the wrong way around.</p>
+class="size-s" alt="lift top" /></p>
+<p>With the phillips head remove the two screws that secure the visible
+part in place and then carefully lift it out, flip it over. There is a
+ribbon cable connecting the touch sensor and LED on the top to PCB
+deeper inside the earpiece.</p>
+<figure>
+<img src="/media/content/sony-wf1000xm3-battery/05_battery_out.jpg"
+class="size-s" alt="battery out" />
+<figcaption aria-hidden="true">battery out</figcaption>
+</figure>
+<p>To remove the old battery I found it easiest to push the spudger into
+the little gap in the plastic where the ribbon cable connects to the top
+part. It is also glued in; be careful not to pull out the contact points
+as well. If possible try to preserve the glue, it will come in handy
+when securing the new battery in place. I also scraped off what was
+stuck to the old battery and pushed it back into the housing.</p>
+<figure>
+<img src="/media/content/sony-wf1000xm3-battery/06_battery_in.jpg"
+class="size-s" alt="battery in" />
+<figcaption aria-hidden="true">battery in</figcaption>
+</figure>
+<p>Before putting in the new battery make sure to check the writing on
+it or use the shape as a reference to figure out which side is the
+negative pole. Put that side down, touching to the contacts. The
+replacement batteries I got where a different brand and had all the
+labeling on the plus pole. While the original VARTA branded batteries
+had it exactly reversed. On my first attempt I didn’t pay attention and
+put them in the wrong way around.</p>
 <figure>
 <img src="/media/content/sony-wf1000xm3-battery/battery_comparison.jpg"
 alt="battery comparison" />
-- 
cgit 1.4.1